BMW M6 (e24) restaurācija

Jautājumi par automašīnu remontu
Lietotāja avatars
RIXCAR
Atbildes: 5
Pievienojies: 19.12.2013, 14:03

18.02.2014, 12:48

RIXCAR car restoration workshop is located in Riga - the capital of Latvia. The company has seven year experience in car restoration processes, at the moment there are 14 employees in RIXCAR and each of them is a master in his field.

The main focus areas are:
-car body repairs and painting
-classic car restoration
-exhaust system tuning
.
This will be a little bigger poster from us, but it might be quite interesting reading material. So we have got a BMW M6 E24 here.
Our aim was to restore the bodywork.
The place where everything happened: RIXCAR
So, when the car arrived, its condition was not very good. The body was damaged and there were a lot of rust.
Attēls
Attēls
Attēls
Attēls
Attēls

To start the restoration process, we removed all the lights, bumpers, etc.
Attēls
Attēls
Attēls
Attēls

We cut out all the rusted parts and fitted the new ones.
Attēls
Attēls
Attēls
Attēls
Attēls
Attēls


We welded all the places where it was necessary.
Attēls
Attēls
Attēls

Car's front corners after welding. The corner is hand made.
Attēls

The car is ready for painting
Attēls

Attēls

Attēls

Attēls

Here we see the body after the primer base coat is applied. Body panels have been fitted to see if they match.
Attēls
Attēls
There is a long story about the front fenders. Since it is close to impossible to find new fenders, we managed to get fenders made from fiber glass.
During the time when the car and panels were prepared for painting, we fabricated brand new Magnaflow exhaust system.
Attēls



The car after painting process.

Attēls
Attēls
Attēls
Attēls

After that we started to put the parts together: interior, overfenders, bumpers, body panels and many other parts.
Attēls
Attēls
Attēls
Attēls

Then we drove the car outside to wash off all the dust.
Attēls
Attēls

After a short while the coilovers arrived, special thanks to ADparts.eu.
Then the windows were put back and we started fitting the coilovers.
Attēls
Attēls
Attēls

To put back the coilovers, steering knuckles had to be modified.
Attēls
Attēls
Attēls
The back of the car will be lowered more and the comfort springs will be removed.

Moldings and bumpers were fitted.

Attēls
Attēls

The car is getting back it’s original look.
Attēls
Attēls
Attēls
Attēls
Attēls

Our BMW M6 E24 is almost finished
The rear bumper still needs to be adjusted. Lights and the whole car are not yet polished. The front chrome molding and fog lights will be fitted by the car owner himself.
In these photos you can see the BBS RK 8,5j et15 wheels.
Attēls
Attēls
Attēls
Attēls
Attēls
Attēls
Attēls


The car is traveling back to Norway.
Final pictures from harbour:
Attēls
Attēls
Attēls
Attēls
Attēls
The car has been returned to the owner, this project is finished. We hope that it was interesting to read and to see the pictures from the process.
Our other projects can be seen here:
http://www.facebook.com/rixcar
http://www.rixcar.lv

Contacts:
Reinis Jansons
Phone: +371 26414411
E-mail: reinis@rixcar.lv
Lietotāja avatars
Omis
Nereģistrējies

18.02.2014, 19:44

Superīgs skaistulis izglābts no nāves!!!
Atbildēt